[Go to CFHT Home Page] Man Pages
Back to Software Index  BORDER=0Manpage Top Level
    buf(9S) manual page Table of Contents

Name

buf - block I/O data transfer structure

Synopsis


#include <sys/types.h>
#include <sys/buf.h>
#include <sys/ddi.h>
#include <sys/sunddi.h>

Interface Level

Architecture independent level 1 (DDI/DKI).

Description

The buf structure is the basic data structure for block I/O transfers. Each block I/O transfer has an associated buffer header. The header contains all the buffer control and status information. For drivers, the buffer header pointer is the sole argument to a block driver strategy(9E) routine. Do not depend on the size of the buf structure when writing a driver.

It is important to note that a buffer header may be linked in multiple lists simultaneously. Because of this, most of the members in the buffer header cannot be changed by the driver, even when the buffer header is in one of the drivers’ work lists.

Buffer headers are also used by the system for unbuffered or physical I/O for block drivers. In this case, the buffer describes a portion of user data space that is locked into memory.

Block drivers often chain block requests so that overall throughput for the device is maximized. The av_forw and the av_back members of the buf structure can serve as link pointers for chaining block requests.

Structure Members

intb_flags;/* Buffer status */
struct buf*av_forw;/* Driver work list link */
struct buf*av_back;/* Driver work list link */
unsigned intb_bcount;/* # of bytes to transfer */
union {
r 2 l 2 l.
caddr_tb_addr;/* Buffer’s virtual address */
l 2 l 2 l.
} b_un;
daddr_tb_blkno;/* Block number on device */
diskaddr_tb_lblkno;/* Expanded block number on device */
unsigned intb_resid;/* # of bytes not transferred */
longb_bufsize;/* size of allocated buffer */
int(*b_iodone)();/* function called by biodone */
intb_error;/* expanded error field */
void*b_private;/* "opaque" driver private area */
dev_tb_edev;/* expanded dev field */

The members of the buffer header available to test or set by a driver are as follows:

b_flags stores the buffer status and tells the driver whether to read or write to the device. The driver must never clear the b_flags member. If this is done, unpredictable results can occur including loss of disk sanity and the possible failure of other kernel processes.

Valid flags are as follows:

B_BUSY
indicates the buffer is in use. The driver may not change this flag unless it allocated the buffer with getrbuf(9F) , and no I/O operation is in progress.
B_DONE
indicates the data transfer has completed. This flag is read-only.
B_ERROR
indicates an I/O transfer error. It is set in conjunction with the b_error field. bioerror(9F) should be used in preference to setting the B_ERROR bit.
B_PAGEIO
indicates the buffer is being used in a paged I/O request. See the description of the b_un.b_addr field for more information. This flag is read-only.
B_PHYS
indicates the buffer header is being used for physical (direct) I/O to a user data area. See the description of the b_un.b_addr field for more information. This flag is read-only.
B_READ
indicates data is to be read from the peripheral device into main memory.
B_WRITE
indicates the data is to be transferred from main memory to the peripheral device. B_WRITE is a pseudo flag that occupies the same bit location as B_READ . B_WRITE cannot be directly tested; it is only detected as the NOT form of B_READ .

av_forw and av_back can be used by the driver to link the buffer into driver work lists.

b_bcount specifies the number of bytes to be transferred in both a paged and a non-paged I/O request.

b_un.b_addr is the virtual address of the I/O request, unless B_PAGEIO is set. The address is a kernel virtual address, unless B_PHYS is set, in which case it is a user virtual address. If B_PAGEIO is set, b_un.b_addr contains kernel private data. Note that either one of B_PHYS and B_PAGEIO , or neither, may be set, but not both.

b_blkno identifies which logical block on the device (the device is defined by the device number) is to be accessed. The driver may have to convert this logical block number to a physical location such as a cylinder, track, and sector of a disk. This is a 32-bit value. The driver should use b_blkno or b_lblkno, but not both.

b_lblkno identifies which logical block on the device (the device is defined by the device number) is to be accessed. The driver may have to convert this logical block number to a physical location such as a cylinder, track, and sector of a disk. This is a 64-bit value. The driver should use b_lblkno or b_blkno, but not both.

b_resid should be set to the number of bytes not transferred because of an error.

b_bufsize contains the size of the allocated buffer.

b_iodone identifies a specific biodone routine to be called by the driver when the I/O is complete.

b_error may hold an error code that should be passed as a return code from the driver. b_error is set in conjunction with the B_ERROR bit set in the b_flags member. bioerror(9F) should be used in preference to setting the b_error field.

b_private is for the private use of the device driver.

b_edev contains the major and minor device numbers of the device accessed.

See Also

strategy(9E) , bioerror(9F) , clrbuf(9F) , getrbuf(9F) , physio(9F) , iovec(9S) , uio(9S)

Warnings

Buffers are a shared resource within the kernel. Drivers should read or write only the members listed in this section. Drivers that attempt to use undocumented members of the buf structure risk corrupting data in the kernel or on the device.

Table of Contents